Grizzly G0602 review: a 10 x 22 lathe with hardened ground V-ways
A heavier benchtop lathe with a gearbox, written from the specifications.
WorkshopCalc is an Amazon Associate and a Grizzly Industrial affiliate. We earn from qualifying purchases.
Grizzly G0602 10 x 22 Benchtop Metal LatheA 432 lb benchtop lathe with six speeds from 150 to 2400 RPM, an MT4 spindle taper, MT3 tailstock, 9 longitudinal feeds and spindle reversing.
Who it is for
- A home machinist who has outgrown a small lathe and wants a gearbox for threads and feeds.
- Someone who needs the 22 in bed and the larger 25 mm bore.
- A shop with a stout bench or a stand rated for 432 lb.
- Anyone who wants an included kit: 5 in 3-jaw, 6-1/2 in 4-jaw, 8 in faceplate, rests and change gears.
Who should skip it
- Anyone short on space or with a weak bench. The footprint is 47-1/2 by 12-1/2 in and the machine is heavy.
- Buyers wanting a variable-speed electronic drive.
- People who only turn small parts, where the G4000 or a mini lathe does the job.
Specifications
| Spec | Detail |
|---|---|
| Motor | 1 HP, 110V, 13.6A |
| Swing over bed | 9-1/2 in |
| Swing over cross slide | 6-1/8 in |
| Distance between centers | 22 in |
| Spindle bore | 25 mm |
| Spindle speeds | 6 speeds, 150 to 2400 RPM |
| Spindle | 1-3/4 x 8 TPI thread, MT4 taper |
| Tailstock | MT3 |
| Inch threads | 31 threads, 8 to 72 TPI |
| Metric threads | 26 threads, 0.25 to 3.5 mm |
| Longitudinal feeds | 9 |
| Footprint | 47-1/2 x 12-1/2 in |
| Ship weight | 432 lb |
| Ways | Hardened ground V-ways, enclosed oil-bath gearbox, spindle reversing |
What the spec sheet does not tell you
A gearbox changes how you work. On a lathe without one, cutting a thread means swapping change gears. With the G0602, 31 inch threads and 26 metric threads are available through the gearbox and the included change gears, so the machine suits repeated threading jobs. The gear ratio calculator is the tool for planning any change gear set.
The 13.6A draw at 110V is the practical limit for a household circuit. Give the lathe its own 20A circuit, and do not run it on a branch shared with a space heater or a compressor. A bigger-looking machine running on a modest 1 HP motor still takes light to moderate cuts; the extra mass improves rigidity, not power.
Hardened and ground V-ways are the detail that separates a better benchtop lathe from a basic one, because the ways guide the carriage and wear over years of cuts. An enclosed oil-bath gearbox also keeps lubrication consistent. Both are design choices that raise the cost of manufacture and show up in the 432 lb weight.
The weight and length matter before the performance does. A 47-1/2 in long machine needs a bench that supports the whole length, and 432 lb will arrive on a freight truck. Plan a path in, plan the floor loading and level the lathe with shims, because a twisted bed cuts tapers.
Think about the tooling that comes with a bigger lathe. The 5 in 3-jaw and 6-1/2 in 4-jaw chucks, the 8 in faceplate and the rests are a good start, but you will want quality tool holders, inserts and measuring tools. A bench that supports the full 47-1/2 in length without sagging is the other half of the install, and cheap lathes on weak stands are a common source of chatter that gets blamed on the machine.
The honest weakness
The honest weakness is that 1 HP on 110V is the same power class as smaller machines, so the extra weight does not buy heavy roughing. The six belt speeds also limit flexibility compared with an electronic variable-speed drive, and the 432 lb weight makes it a fixed install. Buyers who want a lathe-mill combination should read the G0769 review instead.
Grizzly direct vs Amazon
Grizzly sells this lathe direct, with the manual and parts breakdown on the product page. For a 432 lb machine, a single seller handling freight is practical.
The closest Amazon-sold alternative is a 10 x 22 lathe from another brand. Compare the spindle bore, the ways and the gearbox before treating them as equivalent. Pick the Grizzly for its documented specifications and parts support.
MechMaxx 10" x 22" Benchtop Metal Lathe, 1.5HP Brushless MotorThis is the nearest match we could find on Amazon in the same class. It is a different machine from the Grizzly, so compare the spec sheets side by side rather than assuming they are equivalent.
Alternatives worth considering
Grizzly G4000 9 x 19 Benchtop Metal LatheThe G4000 has a 3/4 HP motor, a 19 in bed and a 20 mm bore at 294 lb.
The G0704 is a 7 x 27 mill/drill, the machine many shops add after a lathe.
MechMaxx 10" x 22" Benchtop Metal Lathe, 1.5HP Brushless MotorA 10 x 22 benchtop lathe with a 1.5 HP brushless motor and a listed 38 mm bore.
Keep reading
- Best metal lathes
- Grizzly G4000 review
- Grizzly G4000 vs G0602
- Grizzly G0704 review
- Feeds and speeds
- Gear ratio calculator
- Electrical load calculator
Common questions
How big is the G0602?
10 in nominal swing (9-1/2 in listed over the bed) and 22 in between centers, at 432 lb.
What is the spindle bore on the G0602?
Grizzly lists 25 mm.
Does the G0602 have a gearbox?
Yes. It has an enclosed oil-bath gearbox and 9 longitudinal feeds.
Can the G0602 reverse?
Grizzly lists spindle reversing.
This page draws on published manufacturer specifications and design reasoning. We have not tested this machine ourselves, and we say so rather than implying otherwise. Specifications were copied from grizzly.com and can change, so confirm them on the product page before you order. WorkshopCalc is an Amazon Associate and a Grizzly Industrial affiliate. We earn from qualifying purchases.